GRADELINE
Find ContractorsBrowse ServicesRequest Services
Log inAdd Your Business
Find ContractorsBrowse ServicesRequest ServicesFind a ContractorLog inAdd Your Business
GRADELINE/Guides/Hydro excavation

GRADELINE project guide

The complete hydro excavation & daylighting guide

Pressurized water cuts the soil, a vacuum truck lifts it out, and the buried line stays intact. What it costs, when you need it, and how to hire a crew that leaves no strike behind.

By GRADELINE Editorial TeamUpdated October 17, 20267 min read

Start the checklistFind hydrovac crews
  • 01 Know when you need it
  • 02 Scope the job
  • 03 Vet the crew
  • 04 On dig day
  • What it costs
  • FAQ

On this page

  • 01 Know when you need it
  • 02 Scope the job
  • 03 Vet the crew
  • 04 On dig day
  • What it costs
  • FAQ

Find a crew near you

How to get a line daylighted, step by step

  1. Call 811 and wait for the marks. Hydro excavation does not replace the locate, it confirms it.
  2. Use vacuum excavation anywhere you dig inside the tolerance zone around a marked line, usually 18 to 24 inches on each side of the paint.
  3. Tell the crew how many holes, how deep, and what you need to see: top of pipe, depth, size, material or a full exposed run.
  4. Ask for an hourly rate with the minimum, the travel time, and the slurry disposal fee written out separately.
  5. Check that the crew has damage prevention training and that the truck can reach your site.
  6. Get each daylight hole logged with depth, utility type and a photo before it is backfilled.

What hydro excavation crews do

Hydro excavation crews use pressurized water to cut soil and a truck-mounted vacuum to lift the slurry into a sealed tank, so they can dig right next to gas, fiber, water and power lines without striking them. The most common job is daylighting, also called potholing: exposing a buried utility so its true depth and position are known before a bore, trench, pile or foundation crosses it. State one-call laws set a tolerance zone around every 811 mark, usually 18 to 24 inches each side, where mechanical digging is not allowed and soft methods like vacuum excavation are. Crews also dig slot trenches, post and pole holes, valve and manhole repairs, frozen ground and contaminated soil that must be contained. Google Maps has no category for this trade, so most hydrovac companies are listed as excavating or utility contractors.

Send the 811 ticket number, a plan or list of every hole with expected depth, what each hole needs to record, the soil type if known, and where the truck can park relative to the work.

Phase 01 · 4 checks

Know when you need it

Hydro excavation is a non-destructive way to dig. The question is not whether it is better than a backhoe. It is where a bucket would be a gamble.

  1. Paint marks show roughly where a line runs, not its exact depth or edge. State one-call laws set a tolerance zone around each mark, and inside it you must dig by hand or with soft methods. Vacuum excavation is the fastest soft method most states allow.

    Ask: “What is the tolerance zone in this state, and is vacuum excavation an approved method inside it?”

  2. Daylighting, also called potholing or test holing, exposes a buried line at the point where a new bore, trench or pile will cross it. Seeing the real depth lets the driller set the bore path with clearance instead of guessing from a paint line.

    Ask: “Can you pothole every crossing on the bore profile before the rig shows up?”

  3. A hydrovac hose can reach places a machine cannot: between foundations, under tree canopies, inside plant yards, next to live gas and fiber. Because the spoil goes into a sealed tank, it also suits sites where soil has to be contained.

    Ask: “How far can you run hose from the truck, and how much depth can you reach at that distance?”

  4. Heated water cuts frozen soil that would stop a bucket, which keeps winter work moving. The same control makes clean, narrow holes for sign posts, fence and pole bases, valve box repairs and slot trenches with very little restoration.

    Ask: “Does the truck have a water heater, and does heated work change the hourly rate?”

Phase 02 · 4 checks

Scope the job

Hydrovac work is billed by the hour, so the clearer the scope, the shorter the bill. These four details decide most of the price.

  1. A typical daylight hole is about one foot square and three to six feet deep. Give the crew a list or a marked plan of every hole, the expected depth, and the soil if you know it. Clay and caliche dig slower than sand and loam.

    Ask: “Based on this list and this soil, how many holes can you finish per hour?”

  2. Exposing a line is only half the job. Decide up front whether you need top-of-pipe depth, diameter, material, direction, GPS coordinates or survey shots. Subsurface utility engineering projects need that data in a set format.

    Ask: “What do you log at each hole, and in what format will I receive it?”

  3. Hydrovac spoil is wet slurry. It cannot be dumped in a storm drain or on the ground. It goes to a permitted disposal or dewatering site, and some states regulate where it can go. Disposal and dump fees are often a separate line.

    Ask: “Where do you dump the slurry, and is the disposal fee included or billed per load?”

  4. Slurry usually is not reused as backfill. Decide who brings clean fill or flowable fill, who compacts it, and who patches concrete, asphalt or sod. Restoration left out of the scope is the most common surprise on the invoice.

    Ask: “Who backfills and restores each hole, and with what material?”

Phase 03 · 4 checks

Vet the crew

Any truck can make a hole. What you are paying for is an operator who knows what is in the ground and what the law expects.

  1. Ask about operator training in excavation safety, damage prevention and confined space or gas awareness where relevant. Utility owners and pipeline operators often require their own qualification before a crew can work near their lines.

    Ask: “What training do your operators carry, and are you approved by the utilities in this area?”

  2. Full-size hydrovac trucks hold large debris and water tanks but need room and firm ground. Smaller trailer units fit driveways and backyards. A truck that cannot get within hose range of the work adds hours.

    Ask: “What size unit will you send, and how close does it need to park?”

  3. Hourly rates usually include the truck and an operator or two. Look for the minimum charge, portal-to-portal travel, standby time, extra labor, disposal fees and fuel surcharges. Two quotes with the same hourly rate can differ a lot by the end of the day.

    Ask: “Is the clock portal to portal, and what is the minimum billable time?”

  4. Utility strikes are expensive. Ask for a certificate of insurance with general liability and auto coverage, and for references on jobs near gas, fiber or high-voltage lines.

    Ask: “Can you send a COI and two references from work near live utilities?”

Red flags

Walk away if a contractor...

  • Says hydro excavation means you do not need an 811 ticket
  • Will not say where the slurry is dumped
  • Quotes only an hourly rate with no minimum, travel or disposal terms
  • No photo or depth record for each hole
  • Holds the wand close to the line at full pressure
  • No proof of insurance or utility approvals

Phase 04 · 4 checks

On dig day

Four checks that keep the job safe, legal and done once.

  1. Every state requires a locate request before digging, and the ticket must be active on the day of work. Hydro excavation does not exempt anyone from 811. Private lines such as irrigation, lighting and private water service also need to be found.

    Ask: “What is the ticket number, and when does it expire?”

  2. The water is strong enough to cut soil, which means it can damage coatings, older cast iron or thin plastic if the wand is held too close. A good operator keeps the nozzle moving and adjusts pressure near the line.

    Ask: “What pressure do you run near plastic gas and fiber, and how do you approach the line?”

  3. A daylight hole is narrow and deep enough to break an ankle. Holes left open should be covered, plated or coned off, especially in yards, sidewalks and roadways.

    Ask: “How are open holes covered between the dig and the backfill?”

  4. Before backfill, get a photo of each exposed line with a tape measure showing depth, plus the utility type and location. That record protects you if a line is hit later and is often required by the engineer or utility owner.

    Ask: “Will I get the photo log and depth sheet the same day?”

What hydro excavation costs

Most hydrovac work is billed by the hour, commonly $150 to $400 per hour for the truck and operator, with a two to four hour minimum and travel time on top. A single daylight hole often costs $300 to $1,000 depending on depth and soil, and slurry disposal is frequently billed separately per load.

ItemTypical priceWhat it is
Hydrovac truck + operator$150 to $400 / hourMost common billing; larger trucks and two-person crews cost more
Minimum charge2 to 4 hoursMany crews bill a half-day minimum plus travel
Daylight / pothole$300 to $1,000 per holeShallow holes in soft soil at the low end; deep or rocky at the high end
Slurry disposal$100 to $500+ per loadSet by the local disposal facility and haul distance
Backfill and surface patchVariesClean fill, flowable fill, asphalt or concrete repair

Ranges are national and approximate; regional rates, soil, depth and disposal distance move them in both directions.

Common projects

  • Daylighting and potholing utilities before directional drilling, trenching and foundation work
  • Slot trenching, post and pole holes, and valve, curb box and manhole repairs near live lines
  • Frozen ground, tight-access and contaminated-soil digging where the spoil has to be contained

What changes the price

  • Number and depth of holes, soil type, and whether the water needs to be heated
  • Truck size, crew size, hose distance from the truck to the work, and travel time to the site
  • Slurry disposal fees and haul distance, plus who handles backfill and surface restoration

811, tolerance zones & disposal rules

Every state requires an 811 locate request before digging, including vacuum excavation. Inside the tolerance zone around a mark, state law limits digging to hand tools or soft methods, and most states accept vacuum excavation. Hydrovac slurry must go to an approved disposal or dewatering site, never a storm drain.

Common questions

What is hydro excavation?

Hydro excavation uses pressurized water to break up soil and a powerful vacuum to lift the slurry into a holding tank on a truck. It digs without a bucket touching the ground, so buried pipes and cables are far less likely to be damaged.

What is daylighting?

Daylighting, also called potholing, is digging a small hole to expose a buried utility so you can see its exact depth, size and position. It is usually done with hydro or air vacuum excavation before boring, trenching or other digging near the line.

How much does hydro excavation cost?

Most crews bill by the hour, commonly $150 to $400 per hour for the truck and operator, with a two to four hour minimum. A single daylight hole often lands between $300 and $1,000. Travel, slurry disposal and restoration are frequently billed separately.

Do I still need to call 811?

Yes. Every state requires a locate request before digging, including vacuum excavation. Hydro excavation is how you safely confirm the marked lines, not a replacement for marking them.

Is hydro excavation better than air excavation?

Water cuts hard, dense and frozen soils faster and is the most common choice. Air excavation leaves dry spoil that can be reused as backfill and is preferred near sensitive electrical gear or where slurry disposal is a problem. Many crews offer both.

Why can I not find hydro excavation companies on Google Maps?

Google Maps has no dedicated business category for hydro excavation or daylighting, so these crews usually list themselves as excavating contractors, utility contractors or septic services. GRADELINE tags them by the work they do so you can find them directly.

Sources

  • Common Ground Alliance, Best Practices: Tolerance Zone, commongroundalliance.com
  • 811, Call Before You Dig, call811.com
  • OSHA 29 CFR 1926.651, Excavation requirements, osha.gov
  • PHMSA, State damage prevention law summaries, phmsa.dot.gov

This guide is general information, not legal or engineering advice. Tolerance zones, disposal rules and licensing vary by state and utility owner. Confirm the rules with your state one-call center and the utility owners before you dig.

Keep researching

Excavation guideTrenching & underground contractorsYard grading guideExcavation in CaliforniaExcavation in TexasExcavation in Florida

0 of 16 checked

GRADELINE

Find a local crew to get your dirt moving. Run a crew? Claiming your page is free.

DirectoryBrowse ContractorsServicesRequest Services
For ContractorsAdd Your BusinessVerified GRADELINE
ResourcesResourcesExcavation Hiring ChecklistAll Guides
CompanyAboutPressSupport

© 2026 GRADELINE. All rights reserved.

PrivacyTerms